Hey guys my name is Eric, Im a pre-med student at MWSU.I drive a 2005 Lancer Evolution 8 which is looking to run 10s this season (after a bit more work) I'm looking at getting an EK hatch. MY first car was a eg hatch and i miss it a bunch so now that i have some extra money i would like to start up another honda build.

 

Welcome to HCF.....lets see some pics of your yellow evo...
and if you get a Ek hatch good luck...sounds like you would do it right...

 

we demand pics of your evo.



oh yeah, welcome!

 

Here are some pics:

http://i41.photobucket.com/albums/e2.../HIDKit1-1.jpg

Freshly Ported Head with Full-Race manifold:
http://i41.photobucket.com/albums/e2...76_34_full.jpg

Ready for the new motor:
http://i41.photobucket.com/albums/e2...y/IMG_0818.jpg

http://i41.photobucket.com/albums/e2...y/IMG_0817.jpg

http://i41.photobucket.com/albums/e2...y/IMG_0816.jpg

Motor:
http://i41.photobucket.com/albums/e2...lly/MOTOR1.jpg

http://i41.photobucket.com/albums/e2...lly/MOTOR2.jpg

Had to get the Corvette in this one:
http://i41.photobucket.com/albums/e2...lly/MOTOR3.jpg

Motor with stock Exhaust Manifold:
http://i41.photobucket.com/albums/e2...y/100_0708.jpg

http://i41.photobucket.com/albums/e2...y/100_0715.jpg

Finished!
http://i41.photobucket.com/albums/e2...y/100_0716.jpg

Modification List as of Right Now:
-Cheapo Turbo Back Exhaust
-Tial 50mm BOV
-Full-Race Exhaust Manifold - Sold to use ported stock manifold for sleeper setup
-Walbro 255 Fuel Pump
-Buscher Intake - Sold, Running Open Turbo and GM MAF
-Manley Rods
-Mahle Pistons
-ACL Race Rod Bearings
-Clevite Thrust Bearings
-Clevite Main Bearings
-ARP Head Studs
-ARP Main Studs
-ARP Flywheel Bolts
-Eibach Pro Springs
-Garrett Dual Ball Bearing GT30R Turbine
-Race Head by Precision Engineering
* 5 Angle Valve Job
* New Valve Stem Seals
* Undercut Valves
* New Valve Guides
* New Floors and Ceilings
* Gasket Match Porting
* EGR Delete
-Cometic 86mm Head Gasket
-Block Work by Precision Engineering
* Hot Tanked
* Compression Tested
* Overbore .040
* Honed
* Balanced
-Aeromotive FPR
-Greddy IC Piping
-Tial 44mm Wastegate
-Greddy / Trust Intercooler
-RC 750cc injectors
-ACT 2600 Clutch 6Puck Un-Sprung
Future Modifications
-Driveshaft Shop Rear and Front Axles
-Shep Transmission
-Shep Transfer Case
*Shep REM/Cryo
Non Performance Upgrades
-VIS CF Hood
-Seibon CF Trunk
-APR Mirrors
-AEM Guages
*Tru Boost
*UEGO Wideband
-Autometer Gauges
*Z series Oil Pressure
-Rota 18x8 Wheels, FOR SALE, Changing to Enkei RPF1's
-Greddy Counterweight Shift ****
-Evo IX Recaro Seat Swap

Future Modifications
-APR Wind Splitter
-APR Canards
-KDW T/A Tires
-Evo 8 Jdm Rear Bumper
-Varis Rear Diffuser
-Rexspeed Small rear spoiler

There is still a bunch of stuff to do until she is "Done" Im still waiting on an AEM EMS and a new fuel system and in the near future a GT35R Turbo. It's just a project.

Yeah I really want to build a white EK hatch. Im really into the Jdm scene.