RE: DiDDeR's D-Series Turbo Project (Updated page 1! LOOK!)

Printable Version

Honda Civic Forum >> General Automotive >> HCF Project Section >> RE: DiDDeR's D-Series Turbo Project (Updated page 1! LOOK!)

Page: <<   < prev  18 19 20 21 [22]

Login Message << Older Topic   Newer Topic >>

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/5/2008 2:36:10 PM    didder Posts: 457 Joined: 4/28/2007 From: Shafer, MN Status: offline this ones calibrated, and they do a million of them, so i felt like id be safer with it. it was probably 50 bucks more than if i bought oem and had it shimmed and ported.. i just felt safer doing it this way. _____________________________ (in reply to GReddy_Civic) Post #: 211

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/5/2008 2:37:41 PM    GReddy_Civic Posts: 1633 Joined: 12/15/2006 Status: offline i guess, since you said youre gonna be pushin 400+ hopefully...im only aimin for 250ish _____________________________ Surf Wagon1994: might be getting a toy :D Forty4U2BNVS: I've been known to toot a pipe or two (in reply to didder) Post #: 212

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/5/2008 3:12:45 PM    didder Posts: 457 Joined: 4/28/2007 From: Shafer, MN Status: offline mehh, 400+ is to hard on motor without sleeves, im shooting for 300+ on mustang dyno (about 345ish on a regular dynomometer) but that will still put me in the 11's hopefully with the full throttle shift and all the traction crap i bought. _____________________________ (in reply to GReddy_Civic) Post #: 213

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/5/2008 3:51:39 PM    GReddy_Civic Posts: 1633 Joined: 12/15/2006 Status: offline i stopped rememberin what you were doin to this...its been so long since it was started and all _____________________________ Surf Wagon1994: might be getting a toy :D Forty4U2BNVS: I've been known to toot a pipe or two (in reply to didder) Post #: 214

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/5/2008 4:11:48 PM    didder Posts: 457 Joined: 4/28/2007 From: Shafer, MN Status: offline look at page 1, its kinda gone bigger than i wanted... original setup was 8lbs of boost shooting for 180-190whp on stock d16y8 now its fully built bottom, top, every traction upgrade i can think of, and anything that can help efficiancy and or durability of the build. shooting for 300+whp _____________________________ (in reply to GReddy_Civic) Post #: 215

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/5/2008 7:56:11 PM    GReddy_Civic Posts: 1633 Joined: 12/15/2006 Status: offline did you think about block guard? not as good as sleeving but if you do it right, you wont contrict flow too awfully bad _____________________________ Surf Wagon1994: might be getting a toy :D Forty4U2BNVS: I've been known to toot a pipe or two (in reply to didder) Post #: 216

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/6/2008 12:30:45 AM    didder Posts: 457 Joined: 4/28/2007 From: Shafer, MN Status: offline block gaurd already pressed in place my friend , only thing the entire motor is missing for beefiness is the sleeves. _____________________________ (in reply to GReddy_Civic) Post #: 217

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 4/6/2008 8:15:03 AM    GReddy_Civic Posts: 1633 Joined: 12/15/2006 Status: offline youre skimpin out on me here! cheap *ss _____________________________ Surf Wagon1994: might be getting a toy :D Forty4U2BNVS: I've been known to toot a pipe or two (in reply to didder) Post #: 218

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 5/3/2008 5:12:34 PM    didder Posts: 457 Joined: 4/28/2007 From: Shafer, MN Status: offline ok i know ive said this a hundred times... but its almost done. install is going down on the 16th, i just need to order up some differential bearings for the obx lsd and get my synchro gears to start the install. i will be breaking in the motor for 500 miles on the chrome basemap (watching my a/f's VERY closely and putting in a 4 pound spring) then ill purchase the s300 and get err tuned to hopefully 340+whp... Wish me luck _____________________________ (in reply to GReddy_Civic) Post #: 219

RE: DiDDeR's D-Series Turbo Project (Updated page 1! LO... - 5/13/2008 9:13:20 PM    croninc   Posts: 223 Joined: 2/23/2008 From: San Leandro Status: offline damn she is gunna be screammmminnnnnnnggggggg (in reply to didder) Post #: 220

Today's Posts
Most Active Topics
Make A Donation
Forum Rules & FAQ
RSS Feeds

Honda Civic Prices

Honda Civic
Civic Si Concept

Featured Sponsors
Select A Model Accord CR-V Civic Civic Hybrid Element Fit Odyssey Pilot Ridgeline S2000

Top 10 Posters
forty04 14155 remmy 11161 fiirkan 10321 mill$civic 8433 marty 8262 mxs 8005 nail i3unny 7705 sacicons 7674 fliphkd720 7589 pete 7169

New Vendors
AMSOIL - Performance Oil Technology
K&N Engineering, Inc.